Henny Penny Pressure Fryer Solenoid Valve Complete Set 24V/50Hz Part No. 29698

Important: Please select the correct version for your country before purchasing. This listing is for the 24V 50Hz version, Part No. 29698, for Henny Penny fryers fitted with a 24V low-voltage control circuit. It is suitable for the UK, Europe, Australia and other 50Hz countries. For 24V 60Hz fryers in the USA or Canada, use Part No. 29515 instead.

Henny Penny 29698 24V Steam Solenoid Valve

This replacement solenoid valve is designed for compatibility with specified Henny Penny commercial pressure fryers fitted with a 24V control circuit. The valve closes at the start of the cook cycle and opens when the cycle ends to release pressure.

If a fryer is not building or holding pressure during the cook cycle, a worn or faulty solenoid valve may be one possible cause. Confirm the existing part number, control voltage, electrical frequency and fryer model before ordering.

Compatible Henny Penny Pressure Fryer Models

For Henny Penny pressure fryers fitted with 24V control circuits, this part is compatible with: PFE-500, PFE-561, PFE-580, PFE-581, PFE-582, PFE-600, CFA-500, CFA-600, Computron 7000 series and CFG gas models.

Which Version Do I Need?

• 24V, 50Hz: Part No. 29698, this listing
• 24V, 60Hz: Part No. 29515
• 208–240V mains, 50Hz: Part No. 18724
• 208–240V mains, 60Hz: Part No. 18721

Check the wiring diagram inside the fryer side panel, or measure across the solenoid terminals. A 24V coil reads approximately 2.2 Ohms resistance.

Specifications

• Part number: 29698
• Voltage: 24 VAC
• Frequency: 50 Hz
• Valve size: ½ inch NPT
• Operation: Normally open (N/O)
• Maximum pressure: 15 PSI
• Maximum temperature: 300°F / 149°C
• Coil resistance: 2.2 Ohms
• Repair kit: Part No. 17120, sold separately
• Replacement coil: Part No. 29575, 24V 50Hz, sold separately

Installation Notes

Disconnect power before replacement. The solenoid coil wires can be connected in either order. If only the coil is faulty, Part No. 29575 can be fitted without replacing the full valve body. Where Teflon seals are worn, repair kit Part No. 17120 can be used to repair the valve.

Frequently Asked Questions

Which Henny Penny fryers does Part No. 29698 fit?

Part No. 29698 is listed for PFE-500, PFE-561, PFE-580, PFE-581, PFE-582, PFE-600, CFA-500, CFA-600, Computron 7000 series and CFG gas models fitted with a 24V control circuit.

Is this valve suitable for UK and European Henny Penny fryers?

Yes, where the fryer has a 24V control circuit and operates on a 50Hz supply. Always verify the voltage and frequency before ordering.

What is the difference between Part No. 29698 and Part No. 18724?

Part No. 29698 is a 24V 50Hz valve for low-voltage control circuits. Part No. 18724 is for 208–240V mains, 50Hz applications.

What should I check before ordering?

Confirm the existing part number, fryer model, 24V control voltage and 50Hz electrical frequency. The coil resistance for this 24V version is approximately 2.2 Ohms.

This is an aftermarket replacement part designed for compatibility with the Henny Penny models listed above. Henny Penny® is a registered trademark of Henny Penny Corporation. This listing is not affiliated with or endorsed by Henny Penny Corporation.

No technical specifications available for this product.